Search:

Type: Posts; User: CPESystems

Page 1 of 13 1 2 3 4

Search: Search took 0.03 seconds.

  1. C114MD Portable pump with 1 1/2 HP S.S. motor and VFD

    We have lots of 1 1/2 HP pumps in stock. In fact we have stock in all sized from 1/2 Hp to 5 HP. If you want 7 1/2 HP or anything larger we have those as well but it will take a couple of weeks...
  2. Replies
    2
    Views
    329

    I sell pumps but still like the gravity idea. ...

    I sell pumps but still like the gravity idea.

    CO2 is heavier than air so if you purge your fermenter slowly from the bottom all the oxygen will be pushed out the top. Then I would leave a...
  3. Replies
    10
    Views
    266

    If you are going to upgrade to a 1 1/2 HP motor,...

    If you are going to upgrade to a 1 1/2 HP motor, get a 3 phase motor and a VFD. You will thank yourself for years to come.
  4. Replies
    10
    Views
    266

    cavitation

    You could try adding BF valve on the outlet to create a little back pressure. This would reduce the flow and the cavitiation, if that is what it is.

    You will know if it is cavitating, it...
  5. Brand New C114MD portable pump with 3 HP SS motor and US made VFD in stock

    Brand New C114MD portable pump with 3 HP SS motor and US made VFD in stock

    48934

    Ckick here for more information and to view the pump on our website.

    Other sizes are available too of course.
  6. C114MD with a 3 HP

    Hi,

    For a 30 BBL tank a 3 HP centrifugal pump should do the job perfectly.
    48836

    You can view it online by clicking here. 3 HP Pump

    We have them in stock and can ship it in a few days.
  7. It certainly sounds like flow is your issue so...

    It certainly sounds like flow is your issue so either the pump or the heat exchanger is under sized. I would put a pressure gauge on the inlet and the outlet of the heat exchanger and then try it...
  8. What pumps do you have?

    What is the model, HP and RPM of your pumps?
  9. Free Shipping during the Craft Brewers Conference!!!

    Come find us at the Craft Brewers Conference for some Beer, Pinball and Pumps!!! Booth 3835!

    46528
  10. Replies
    9
    Views
    888

    Alfa Laval Carlsberg Flask

    If you want the Alfa Laval Scandibrew Carlsberg Flask we can get you a new one for $8900.00 USD.
  11. Replies
    4
    Views
    503

    You could also put the sensors on the outlet port...

    You could also put the sensors on the outlet port before your shut off valve. However, you will get false readings when pumping out of the tanks.

    Another possible choice would be putting the tanks...
  12. We can certainly supply you with a floor pump but...

    We can certainly supply you with a floor pump but not the keg washer.

    Please check out or pump selection online or email us.


    http://www.cpesystems.com/collections/portable-pumps-and-carts
    ...
  13. Replies
    7
    Views
    575

    Could you post a picture of the valve?

    Could you post a picture of the valve?
  14. Replies
    3
    Views
    675

    That would be much to small for a 7 BBL system. ...

    That would be much to small for a 7 BBL system. It might be good for a homebrewer or a 1/2 BBL pilot system.
  15. Give me a call tomorrow and I will try to help...

    Give me a call tomorrow and I will try to help you figure it out.

    Don
  16. Replies
    5
    Views
    1,892

    Hi, Just so there aren't any surprises that...

    Hi,

    Just so there aren't any surprises that is a THOMSEN pump with a BALDOR 1 1/2 HP single phase motor.
  17. Replies
    5
    Views
    902

    Pressure gauges are a good idea but you are...

    Pressure gauges are a good idea but you are right, if you throttle the water in and the wort out you should be fine.

    Re: inlets and outlets on top and bottom. It depends on the the number of...
  18. Replies
    5
    Views
    902

    Throttle the inlet

    You want to keep the water pressure (or glycol) in the chiller as low as possible. Make sure your chiller is flooded with water but throttle the inlet.

    If you throttle the outlet you create...
  19. Replies
    3
    Views
    476

    Ampco Seal kit

    Hello

    We have them as well.

    http://www.cpesystems.com/collections/seals-kits-and-spare-parts/products/c-series-mechanical-seal-kit?variant=32082811524
  20. Replies
    10
    Views
    3,181

    Seal set up

    Like Warren said, the most important thing is to set up the seal correctly and then clean and maintain it properly.

    Here is a link to a YouTube video on how to set up the pump seal on one of...
  21. Replies
    0
    Views
    480

    Big Toys for Big Boys (and girls too)

    CPE is Now Offering Larger Portable Pumps!!!!

    41815
  22. Replies
    6
    Views
    759

    3.5" fitting

    Hi,

    What you have is a 3" SCHED 5 tri-clamp fitting. They are actually quite commonly used for manufactured items like strainers, sightglasses, check valves ect. They probably used this so they...
  23. Replies
    8
    Views
    1,119

    Watlow heaters

    Personally I like Watlow heaters. Many options available, easy to replace and fully UL and CSA approved.

    The approval is very important if you want to pass your electrical inspection.
    ...
  24. Replies
    0
    Views
    674

    Brewery Equipment SALE!

    40751

    Great Deals on select equipment. MOVEMBER Discount on purchases over $250 is applicable to all Black Friday Sales Items! Twice the Discount!!!

    Click Here for more details!
  25. Replies
    9
    Views
    1,167

    "F" Seal

    The simple "F" seal option on a "C" series pump should do the trick.

    http://www.cpesystems.com/collections/pumps-and-motors/products/topline-tf-c114md-pump-with-2-hp-tefc-motor?variant=985689364
Results 1 to 25 of 302
Page 1 of 13 1 2 3 4