Search:

Type: Posts; User: RipRap

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Isn't that part isolated from the beer by that...

    Isn't that part isolated from the beer by that gasket that sits on the little shelf there in the keg? I think the only way to get to that part is to remove the spear and wipe it out, and no keg...
  2. Replies
    4
    Views
    468

    I just buy tri clamp barbs and cheap hose and...

    I just buy tri clamp barbs and cheap hose and make my own. Takes just a few minutes.
  3. Replies
    2
    Views
    446

    Email sent. Very interested.

    Email sent. Very interested.
  4. Replies
    7
    Views
    630

    Get some envelope gaskets. They are teflon on the...

    Get some envelope gaskets. They are teflon on the outside and EPDM/BUNA/Viton on the inside. You get the smooth turning of teflon and the squishability and better sealing of the softer materials. I...
  5. Replies
    7
    Views
    736

    I personally buy from Gopher Kegs. They are about...

    I personally buy from Gopher Kegs. They are about $90 ish a piece for half barrels and I think they have volume discounts as well. Iíll be honest I mostly buy from them because their warehouse is a...
  6. Replies
    29
    Views
    3,022

    I'm honestly surprised you are getting offered...

    I'm honestly surprised you are getting offered anything at all for them. You were paid by the company to develop the recipes for the company, and therefore I would view the recipes as property of the...
  7. I would definitely be interested in being the...

    I would definitely be interested in being the pilot brewery for the kit. If not, I will be definitely be one of the first pre-orders. Well done on all the progress so far!
  8. Mine are the same size tanks and are about the 3...

    Mine are the same size tanks and are about the 3 gallon line. I just dump yeast/dry hops a couple times before I rack over. I do still tend to pull a small amount of yeast into the brite but it just...
  9. Replies
    3
    Views
    374

    I've added tri clamp fittings to plastic conical...

    I've added tri clamp fittings to plastic conical tanks before. Just get a 1/2" bulkhead fitting and a 1/2" npt to tri clamp adapter.
  10. Replies
    4
    Views
    512

    Got some from BizChair

    Got some from BizChair
  11. Sounds like the tank is uninsulated right now and...

    Sounds like the tank is uninsulated right now and he is planning on adding insulation. Interesting about the hot temps breaking down insulation as it is common practice to run hot cleaning cycles....
  12. I have a 400 gal plastic tank in my walk in as a...

    I have a 400 gal plastic tank in my walk in as a CLT, works fantastic. I posted pictures on here not too long ago if you dig through my post history. Takes 2-3 days to drop to temp depending on...
  13. https://www.gwkent.com/proline-ii-keg-filler.html?...

    https://www.gwkent.com/proline-ii-keg-filler.html?gclid=CjwKCAjwxJnNBRAMEiwA8X_-Qb7QKGee88Jz8QN_cp_eYfPRoJQD8J7n5DwPRZ2skH-p5Mipu58bThoCwusQAvD_BwE

    Or just get a coupler, remove the check ball,...
  14. Replies
    11
    Views
    2,232

    Here is the solution I came up with inspired by...

    Here is the solution I came up with inspired by the original post.
    51901
  15. Replies
    6
    Views
    664

    I seem to remember a CBC talk about this...

    I seem to remember a CBC talk about this technique. Look in the BA archives, its probably there.
  16. Replies
    11
    Views
    2,232

    I think I remember this post. They essentially...

    I think I remember this post. They essentially plumbed 4 55 gallon drums together with a float switch and solenoid valve on the inlet of the drums to fill them in the cold box. Then ran that cold...
  17. Replies
    2
    Views
    727

    Very interested. Sent you a PM.

    Very interested. Sent you a PM.
  18. Replies
    4
    Views
    692

    Brewery near me just bought one. They seem to...

    Brewery near me just bought one. They seem to think they are the chinese supplier for Deutsche. Looks decent from what I saw of it briefly but I didnt get a chance to really inspect it closely.
  19. Replies
    20
    Views
    3,164

    There are very few companies that actually...

    There are very few companies that actually manufacture their tanks in the US. Most companies (Stout, Deutsche, Alpha, and many many more) have them made overseas and warehouse and/or assemble them...
  20. I think Plato and Brix are nearly identical....

    I think Plato and Brix are nearly identical. According to this chart (http://www.straighttothepint.com/wp-content/uploads/2016/01/Brix-Plato-SG-Conversion-Table.png) 25.0 Brix is equal to 24.9979...
  21. Replies
    3
    Views
    545

    Thats exactly my setup. I do not remove my...

    Thats exactly my setup. I do not remove my bulkheads when I clean. Haven't had an issue yet. I clean with hot caustic and PAA.
  22. Replies
    5
    Views
    512

    Very interesting. Learn something new every day!

    Very interesting. Learn something new every day!
  23. Replies
    5
    Views
    512

    .75 hp=560 watts 560watts/115v=4.9A At...

    .75 hp=560 watts

    560watts/115v=4.9A

    At least that's my understanding of it.
  24. Replies
    9
    Views
    1,049

    I'll second 34/70. Did a pils with it and it a...

    I'll second 34/70. Did a pils with it and it a few month back and it turned out awesome.
  25. Replies
    6
    Views
    757

    Sorry I dont have specifically what youre looking...

    Sorry I dont have specifically what youre looking for but if youre pushing with CO2 on your keg washer I would assume you are not using caustic on your kegs. Switching to caustic could save you money...
Results 1 to 25 of 73
Page 1 of 3 1 2 3