Hey guys,
Been in the industry for a few years and it's strangely my first time posting here so please bear with me!
Anyways, after working for the last two years to put together my nano while working at a brewpub I'm less than a month from moving all of my equipment into the industrial space I've leased. The pilot sized system I purchased is 1.5bbl, had never been used, and needed a burner. As such I went out and purchased a 160,000 BTU 32-tip jet burner online and began talks with the local plumber about getting it fitted to the gas source in the space. He very quickly raised concerns about the town gas-inspector and his habit of demanding American Gas Association testing and approval on all parts used. As such I contacted the online seller who then contacted the distributor who then contacted the manufacturer (in CHINA!) who then informed me that although the burner is certified for use and used in thousands of restaurants throughout the nation they do not have an AGA approval certification they can give me.
I then found other burners online and contacted their manufacturers. Same story.
Finally I contacted Burners Inc. and explained my problem to an engineer there. He informed me that my town inspector had set an impossible standard to meet as generally only a complete burner "system" complete with shutoffs, piping, solenoids, and controls is approved by the AGA or similar safety certification group. He then pointed out that no such system would exist for my kettle, or perhaps any kettles, as almost all brewery equipment is custom manufactured.
Please, correct me if I'm wrong, but my understanding is that there are hundreds if not a thousand or so direct fired breweries in the U.S. using custom or new burners. The brewpub I currently work at replaced JUST our burner a few years back without a word from any inspector. How can this be? Is my gas-inspector holding me to an impossible standard here? Is there any way to convince this man that these burners are in use in hundreds of brewpubs, micros, and nanos throughout the country?
More importantly, have any of you ever encountered this sort of problem with your local inspectors? If so, how did you deal with it?
I'd really appreciate any advice you have. I'm knee deep in labels, cooling systems, and TTB paperwork and all of a sudden the town blindsides me with this...
Thanks!
-Ben
Been in the industry for a few years and it's strangely my first time posting here so please bear with me!
Anyways, after working for the last two years to put together my nano while working at a brewpub I'm less than a month from moving all of my equipment into the industrial space I've leased. The pilot sized system I purchased is 1.5bbl, had never been used, and needed a burner. As such I went out and purchased a 160,000 BTU 32-tip jet burner online and began talks with the local plumber about getting it fitted to the gas source in the space. He very quickly raised concerns about the town gas-inspector and his habit of demanding American Gas Association testing and approval on all parts used. As such I contacted the online seller who then contacted the distributor who then contacted the manufacturer (in CHINA!) who then informed me that although the burner is certified for use and used in thousands of restaurants throughout the nation they do not have an AGA approval certification they can give me.
I then found other burners online and contacted their manufacturers. Same story.
Finally I contacted Burners Inc. and explained my problem to an engineer there. He informed me that my town inspector had set an impossible standard to meet as generally only a complete burner "system" complete with shutoffs, piping, solenoids, and controls is approved by the AGA or similar safety certification group. He then pointed out that no such system would exist for my kettle, or perhaps any kettles, as almost all brewery equipment is custom manufactured.
Please, correct me if I'm wrong, but my understanding is that there are hundreds if not a thousand or so direct fired breweries in the U.S. using custom or new burners. The brewpub I currently work at replaced JUST our burner a few years back without a word from any inspector. How can this be? Is my gas-inspector holding me to an impossible standard here? Is there any way to convince this man that these burners are in use in hundreds of brewpubs, micros, and nanos throughout the country?
More importantly, have any of you ever encountered this sort of problem with your local inspectors? If so, how did you deal with it?
I'd really appreciate any advice you have. I'm knee deep in labels, cooling systems, and TTB paperwork and all of a sudden the town blindsides me with this...
Thanks!
-Ben
Comment