Originally posted by Jeffhorn83
View Post
Announcement
Collapse
No announcement yet.
Growler Issues
Collapse
X
-
Originally posted by BemidjiBrewing View PostMy math or understanding of the conversation may be off...but if you are running 25psi with 60% N2 and 40% CO2 then your CO2 concentration is essentially at 10psi...40% of 25psi.
10psi @ 38°F = 2.3 Vol/CO2
@ 40°F = 2.2 Vol/CO2
@ 42°F = 2.1 Vol/CO2
These carbonation rates are on the low side, but probably wouldn't be perceived at "flat."
It seems that any scenario that calculates out to his system overcarbonating his beers (hence having to lower the pressure) wouldn't apply being the beer is objectively flat.
Please correct me if I'm wrong on this!
Jeff, are you able to confirm the carbonation in the brite or unitank to ensure that the beer is entering the keg at a known carb level?
Cheers,
Tom
I just realized I didn't exactly answer your question. I can verify the CO2v/v in the brite tank with the Zahm, but I either don't know how to/ don't have a way to verify that the CO2v/v in the keg is the same. How does one go about doing such a thing?
Is it as simple as filling the Zahm from the keg directly, or from the tap? I feel like the gas pushing the beer would throw off the reading. Please advise.
Comment
-
Jeff,
No sweat - I think you did answer it actually! As long as you can verify it in the tank with your Zahm and your keg filling procedure is sound (based on your experience I don't doubt this) the beer should have minimal losses going into the keg. You can rig up the zahm to take a sample out of the keg but I don't know that it is of concern. It seems that it may be the gas blend issue. However, with your updated 60% CO2 data it doesn't seem too out of wack. Being your tests with other brewery's beers resulted in flat beer as well, I would still focus on your draft system.
I know you mentioned head retention issues as well - are you able to verify that the beer actually tastes/feels flat or does it only appear flat due to its lack of head? I'm curious if there is any oil/grease/head destroying compound being introduced somewhere in your draft system. Also, with a long draw system like that can you verify that your glycol levels haven't fluctuated in your trunk line system?
Comment
-
I think the majority of your problem is the gas mixture - at that mix your probably would want to set your pressures at 30 psi to maintain good carbonation, but your line resistance is probably not enough for that pressure. If it is pouring okay now, try increasing the regulator pressures to 30 psi and see how that works for a brand new keg you tapped, that should be properly carbonated.
If you are knocking out a lot of foam when you are filling, you are losing carbonation there.
Also, I have found that the cheap white metal caps for growlers are junk. They don't seal well the first time, and won't work if you reuse them. You can get the black polyseal ones from Grandstand that have a resealable liner, that holds the pressure much better and can be reused.
Comment
-
Originally posted by BemidjiBrewing View PostJeff,
No sweat - I think you did answer it actually! As long as you can verify it in the tank with your Zahm and your keg filling procedure is sound (based on your experience I don't doubt this) the beer should have minimal losses going into the keg. You can rig up the zahm to take a sample out of the keg but I don't know that it is of concern. It seems that it may be the gas blend issue. However, with your updated 60% CO2 data it doesn't seem too out of wack. Being your tests with other brewery's beers resulted in flat beer as well, I would still focus on your draft system.
I know you mentioned head retention issues as well - are you able to verify that the beer actually tastes/feels flat or does it only appear flat due to its lack of head? I'm curious if there is any oil/grease/head destroying compound being introduced somewhere in your draft system. Also, with a long draw system like that can you verify that your glycol levels haven't fluctuated in your trunk line system?
My gas rep is gonna come out next week to do a variety of tests on their system, the glycol lines, the co2 in solution in the lines/ kegs, and other such things. Following that visit, if nothing comes out as odd/off, I'm gonna break down every single faucet and thoroughly clean them myself. Our beer reps are supposed to do that every time they clean a line, but I have no way to verify that this is actually occurring. I'm hoping that by weeks' end next week this issue will be completely resolved and behind me.
I really do appreciate all of the help on this one.
Comment
-
Originally posted by lhall View PostI think the majority of your problem is the gas mixture - at that mix your probably would want to set your pressures at 30 psi to maintain good carbonation, but your line resistance is probably not enough for that pressure. If it is pouring okay now, try increasing the regulator pressures to 30 psi and see how that works for a brand new keg you tapped, that should be properly carbonated.
If you are knocking out a lot of foam when you are filling, you are losing carbonation there.
Also, I have found that the cheap white metal caps for growlers are junk. They don't seal well the first time, and won't work if you reuse them. You can get the black polyseal ones from Grandstand that have a resealable liner, that holds the pressure much better and can be reused.
I mean...any details. This place has been a constant struggle. Every day I find something else wrong.
Comment
-
I'm curious as to why you are using mixed gas for your push. How long are your lines? If they're under 10 feet or so, I'd just go with a straight CO2 push. Since you're buying the N2 in tanks, you aren't saving any money with the mix, and you won't risk badly over-carbing your beer with a short push.
For any long runs that would require too much pressure, I use pneumatic-powered beer pumps. Easy to set up and easy to balance--just adjust the air pressure to the pumps to change the fill rate. You do still need about 12' of 3/16" choker line at the faucets to balance the CO2 pressure, but they give the best pours I've seen.Timm Turrentine
Brewerywright,
Terminal Gravity Brewing,
Enterprise. Oregon.
Comment
-
Originally posted by TGTimm View PostI'm curious as to why you are using mixed gas for your push. How long are your lines? If they're under 10 feet or so, I'd just go with a straight CO2 push. Since you're buying the N2 in tanks, you aren't saving any money with the mix, and you won't risk badly over-carbing your beer with a short push.
For any long runs that would require too much pressure, I use pneumatic-powered beer pumps. Easy to set up and easy to balance--just adjust the air pressure to the pumps to change the fill rate. You do still need about 12' of 3/16" choker line at the faucets to balance the CO2 pressure, but they give the best pours I've seen.
As to why it was set up the way it was...I have no idea. That was before my time here
Comment
-
I know Timm has long advocated for the use of beer pumps and they may be a great option for your long run system!
I'm still a bit boggled as to how the beer pours extremely fast and has no head retention when the CO2 in the blend is at 60% (15psi CO2 when the mixed system is set to 25psi). There seems to be something else here at play besides just the unbalanced system. Mostly, I'm just really curious now!
Comment
-
Bemidji--His N2 is at 60%. Lots of push, not enough CO2.
For lines of 100', you really need beer pumps! I have two systems of 45' each driven from one set of beer pumps, and another system of 18', also w/pumps. The second one was a re-build of an existing gas-pushed system that never poured well, but it has the best pours in town now.
You'll amortize the cost of the pumps rapidly through savings in gas and wasted beer, have better pours, and keep your carbonation right where it should be.
For the latest system I built, there was no compressed air available. I used a 2 gal. contractor's grade low-noise compressor mounted right in the cooler. It keeps up just fine.
BTW--Your 100' lines are glycol-cooled, right?Last edited by TGTimm; 12-27-2017, 11:11 AM.Timm Turrentine
Brewerywright,
Terminal Gravity Brewing,
Enterprise. Oregon.
Comment
-
Took me a while to get back on here, to fill all of you in on the solution to the problem. It was an incorrect mix of our gas blend. Our gas guy came out and did a beer check on the draft lines here and found that our actual mix was running at 56/44. I have since re-calibrated the blender to be set at 72/28 and it has helped enormously. He also provided me with a link to a blend calculator that determines what your "perfect blend" is/ should be set at. It's a pretty great little tool. Takes out the need for all of that fun math that we all hate to do so much. If any of you want to check your system settings, here's the link to the calculator:
Comment
Comment