Search:

Type: Posts; User: Jedi

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    1,755

    Thanks for the response. I am in Canada so the...

    Thanks for the response. I am in Canada so the laws are different. Perhaps the word expecting is was poor, I meant I expected it to happen eventually just not so soon.

    I was on the fence of...
  2. Replies
    7
    Views
    1,755

    Employees skimming/stealing tips

    So we are a new busy brew pub. We expected employee stealing. As a brew pub tip-out goes to the food runner/bus boy and kitchen so tip stealing effects everyone.

    In less than 2 weeks we caught a...
  3. Replies
    15
    Views
    1,881

    Ya I looked at cool fit, I was quoted $17 USD a...

    Ya I looked at cool fit, I was quoted $17 USD a linear foot and I am in Canada so its even worse. I will take a little pain to save that kind of money, lol.
  4. Replies
    15
    Views
    1,881

    Thanks guys! In hindsight, if I had to do it...

    Thanks guys!

    In hindsight, if I had to do it over again I would have done copper. It's worse to have to wrap this stuff vs copper because its so much thicker and the joints are less friendly to...
  5. Replies
    15
    Views
    1,881

    Ya I like the idea of foam, as I hate touching...

    Ya I like the idea of foam, as I hate touching any fiberglass without a hazmat suit lol. I will try the foam on the straits, my elbows don't really sweat they are so thick, but if they do I will try...
  6. Replies
    6
    Views
    1,546

    Ya what's even better is with the 2 instant water...

    Ya what's even better is with the 2 instant water heaters, during sparge mode I set one to 185 and one to 160 and use my mixing station for a little bit of cold blend and we get perfect sparge temps...
  7. Replies
    6
    Views
    1,546

    Ya we got it figured out, they did 2" and 1"....

    Ya we got it figured out, they did 2" and 1". Since we don't use an HLT (instant) and don't double batch its worked out well as our BK valve has to throttle to 65% or the boil is too aggressive even...
  8. Replies
    15
    Views
    1,881

    Thanks man! Oh that's great to know as its a...

    Thanks man!

    Oh that's great to know as its a pain to buy the corners and seal them and the tee's are so bulky, I was dreading it. If I only need to do the strait sections than that saves a lot of...
  9. Replies
    15
    Views
    1,881

    Aquatherm Glycol Piping - Dripping Bad

    We have Aquatherm blue in the brewpub, I was told it didn't need insulation but it clearly does. Its dripping all over really bad, it's like its constantly raining where ever the header run is making...
  10. Replies
    4
    Views
    921

    Thanks guys I will look into those. I have the...

    Thanks guys I will look into those. I have the brewmation Brewhouse with the control panel. I think they want around 5k for the brewmation but that's only 8 tanks. So you have to buy another module...
  11. Replies
    4
    Views
    921

    Remote access based fermentation solutions?

    I'm looking for a a temperature management solution for my fermenters that I can access remotely. I have redundant internet, VPN and redundant servers to run it all. I don't need anything too fancy,...
  12. Thanks Mike! That sounds perfect. The 2" will...

    Thanks Mike! That sounds perfect. The 2" will still need to be welded but so did the 3" low pressure, I'm guessing the pipe drop size will save me 1k.

    Does the return need to be all welded for...
  13. Ya I'm thinking the knowledge is worth learning...

    Ya I'm thinking the knowledge is worth learning too, but I'm so busy on the brewery build its another item for the list.

    I spoke to the local boiler authorities, I can run it at high pressure if I...
  14. Ok thanks, good info. I will ask the boiler...

    Ok thanks, good info. I will ask the boiler authorities if I can keep it High pressure and reduce it. I have a feeling they will say no as technically the boiler itself is still high pressure and I...
  15. I'm not sure what you mean expensive. The...

    I'm not sure what you mean expensive. The controls are super cheap. 120 bucks each and can be installed in minutes.
    ...
  16. Those are good comments. Thanks for helping....

    Those are good comments. Thanks for helping. Actually in this case this boiler is the same product for both high pressure and low pressure. It comes default with a 3" feed outlet and 2" return...
  17. Replies
    6
    Views
    1,546

    Steam Pipe Size Question

    I have a 10hp boiler making a 90ft run to the BK/MT, 10BBL Brewhouse, no HLT as I have an on-demand heated water mixing station.

    - My steam inlet is 3/4" on the vessels.
    - I had one engineer...
  18. I know each state/province there are different...

    I know each state/province there are different rules but the general consensus is I need specific levels of boiler operator licenses and/or certified engineer to operate it if its left at high...
  19. Changing Boiler from High Pressure to Low Pressure Question

    I bought a used 10hp Bryan boiler, it's 150psi.

    I'm going to convert it to low pressure. I called the manufacturer and they do allow it as the unit supports both HP and LP. Bryan is saying the...
  20. Replies
    7
    Views
    2,243

    Has any tried their vermont strain? I heard it...

    Has any tried their vermont strain? I heard it can be finicky due to it being cultivated from heady topper.
  21. Replies
    7
    Views
    2,243

    What's the pricing like compared to say white...

    What's the pricing like compared to say white labs, wyeast?

    Also flocculation is important to me. Take wyeast kolsch yeast and white labs equivalent, the white labs variant has better flocculation.
  22. Replies
    7
    Views
    2,243

    Omega Yeast? Anyone use them?

    Seen the adds for omega yeast on a homebrew newsletter.

    Checked out their yeast list. Seemed pretty standard with a couple unique offerings like vermont and a couple norwegian yeasts, HotHead Ale...
  23. Replies
    7
    Views
    2,221

    Agreed. But if it comes to be an issue you can...

    Agreed. But if it comes to be an issue you can look at ozone generators or ionic fans. Some are even both. These are not cheap, the commercial combo ones start in the low thousands. Both need fresh...
  24. Replies
    13
    Views
    2,023

    Beer pumps are a must, they are not that...

    Beer pumps are a must, they are not that expensive. If your throwing away that much beer they could have been paying for themselves already.
  25. Thanks for the feedback! I have specced an 12...

    Thanks for the feedback!

    I have specced an 12 x 20 cooler. It looks like it will hold 10x 8 BBL serving tanks, plus kegs or 5x 8 BBL serving tanks and 70 kegs stacked between 2-3 kegs high (3 for...
Results 1 to 25 of 98
Page 1 of 4 1 2 3 4