Search:

Type: Posts; User: gitchegumee

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    58

    Nothing special

    I would fill the system with water first. Then turn on the chiller. Check for proper rotation of glycol pump. Check for proper refrigeration operation. Check for leaks. Then drain and refill...
  2. Replies
    8
    Views
    275

    Foamtime....

    What would be any advantage to that? Might be good for a short run with extenuating circumstances, but I'm not going to package beer into a cold room only to take it all apart to label it again at...
  3. Replies
    8
    Views
    275

    Sticker label or shrink label before filling. ...

    Sticker label or shrink label before filling. Date code before filling. After filling is just a quick rinse and then box, six pack rings, or snap tops.
  4. I'm with Rosie...

    Everything I do is in liters. So simple to do any math regarding dosing or ratios or recipe formulation or anything volumetric. Or heat additions, refrigeration, packaging, or almost any...
  5. Replies
    8
    Views
    275

    try Pack Leader

    We used a small table-top unit to apply roll labels to empty cans at the infeed of our canning machine. Even had a hot printer for date coding. Worked quite well for us.
  6. Parallel

    Putting jackets in series also has disadvantage of raising the system pressure. Parallel offers least resistance and greatest heat transfer, which is what you're after. Efficiency.
  7. Replies
    3
    Views
    463

    What Unfermentable said.

    Why would you do that? There is no upside. Only downsides. Normal SOP will treat you right.
  8. Replies
    11
    Views
    4,802

    splices?

    Not sure if you designed your system with a main line that splits off to different taps? If so, that might be your problem. I will never splice my barrier line. Each line should be independent...
  9. +1 for common reservoir

    I've installed many redundant refrigeration systems. The best way I've found is to use the same size chillers and add to the number when you need expansion. Cheaper to stock spares, too! Pro...
  10. Replies
    3
    Views
    140

    Yeah. No.

    Used many dozens of these over the years and never had an issue. If they did leak you'd hear the pump chug when taps are closed. Think your pal might have an irrational fear of these. Push with...
  11. Replies
    8
    Views
    227

    Not where you are!

    I've only purchased these outside the US. The last few times from Rotex. Sure you can find something of equal quality. Beware of dirt cheap crap, however.
  12. Replies
    5
    Views
    297

    I messed that up!

    Been working in godawful English units lately, so my memory did not serve me correctly. One mole (28g) of nitrogen is 22.4 LITERS. Not SCF! So one pound of nitrogen would be 363 liters. Or 12.9...
  13. Replies
    3
    Views
    340

    So what's the problem?

    20psi is fairly typical for a regulator set pressure. Wetting + internal pressure + hydrostatic. Assuming your tank internal pressure is about 13psi, a typical 10bbl BBT height is maybe 6 feet...
  14. Replies
    5
    Views
    297

    Really?

    It's very easy to convert pounds to cubic feet. Ideal gas law: PV=nRT. And remember that 1 mole occupies 22.4 SCF. Or Google! Which tells me that 1 pound of nitrogen is 13.8 SCF.
  15. Replies
    6
    Views
    215

    Angle seat valves

    Are a bit more complicated, I'll give you that. Besides the main angle valve body, they have a pneumatic solenoid pilot. But the failure rate of a small, pneumatic solenoid using dry, clean plant...
  16. Replies
    8
    Views
    227

    Angle seat valves

    Pneumatic Angle seat valves with solenoid pilots are bulletproof, inexpensive, and reliable. Wouldn't use anything else.
  17. Replies
    6
    Views
    215

    Don't do it!

    If you're going to replace solenoids with something more robust, then I suggest air-operated angle seat valves. Good ones are around $100 or so. They are bulletproof and highly reliable. A few...
  18. Replies
    7
    Views
    374

    Stick with plan A

    That device looks like far more trouble than it's worth. Putting gas on a cold keg for a week would be far superior, IMO. How are you going to "9) serve beer"? Through the stone? That's a...
  19. Something else...

    2 hours mashing is extreme. I use 20% boiled rice and a 20 minute saccharification rest. That is plenty! Attenuation is down to 1.65P for a very dry beer. You do not require gelatinization of...
  20. Replies
    2
    Views
    303

    You get what you pay for.

    Going cheap is most often not in your long-term best interests. I would not spend my money there unless I was looking over their shoulders 100% of the time. And that's not worth my time; nor what...
  21. Replies
    3
    Views
    282

    They won't make a custom door....

    Your door is very likely mass produced by a large door manufacturer. Just need to find the distributor for that manufacturer. Don't know who BRD used, but many companies used Zorzini.
  22. Replies
    3
    Views
    282

    Look around...

    First: single walled brite tank? So basically a cooler-housed serving tank? Most manufacturers do not make their own doors. Doors are usually purchased from other suppliers. Check out companies...
  23. Replies
    7
    Views
    451

    I'd go for it.

    The boiler may be marginally adequate, but you need to know what pressure the steam is delivered and then the jacket size of the kettle. Can't easily put a low pressure boiler on a jacket made for...
  24. Replies
    5
    Views
    525

    Archon Industries

    Whether DIN or SMS gaskets & fittings, you can find either here. Plus lots of other goodies that you might need. Maybe even butterfly valve seals (which may be shot). BTW, your HX gaskets may be...
  25. Replies
    5
    Views
    408

    Monarch 1110

    Proven on tens of thousands of can bottoms. Buy the best before stickers at U-line or anywhere else.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4