Search:

Type: Posts; User: lhall

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Has anyone had a chance to try this yeast?

    Has anyone had a chance to try this yeast?
  2. Replies
    11
    Views
    662

    Watch out putting a floor drain inside your keg...

    Watch out putting a floor drain inside your keg cooler. I had a plumbing inspector require a backflow preventer on a floor drain in our cooler, because it was a "food-storage unit" and we couldn't...
  3. Tom, It probably depends on the type of...

    Tom,

    It probably depends on the type of insulation. We had the exact same thing happen. We ended up having to cut the cladding off the outside to get to the weld to fix it. The insulation was a...
  4. Replies
    3
    Views
    514

    Yeah, I like Burkert valves on our keg washer. ...

    Yeah, I like Burkert valves on our keg washer. We have a bunch of these air canister actuators that mount on top of a standard butterfly valve stem, like a Tassalini or Defonix valve. The canister...
  5. Replies
    3
    Views
    514

    pneumatic valve actuators

    I'm looking for a good single-action, spring-return air valve actuator for our butterfly valves. The ones that originally came with our Newlands brewhouse can't be repaired once they start leaking...
  6. Replies
    14
    Views
    1,491

    Not to be negative - but you should go with...

    Not to be negative - but you should go with hydraulic-pressed fittings on hoses that you use for CIP. A banded hose will fail someday, with the hose popping off the barbed fitting under pressure,...
  7. Replies
    8
    Views
    874

    I believe that the need for a pressure vessel to...

    I believe that the need for a pressure vessel to be ASME rated is when it is 120 gallons or larger. Not sure of the exact volume, but kegs are smaller than whatever it is.
  8. Replies
    5
    Views
    643

    Hmm. Several things pulling too many amps all of...

    Hmm. Several things pulling too many amps all of a sudden? Sounds like a low voltage condition, or losing one leg of a three-phase system. Has your electrician checked the voltage to that panel?
  9. Replies
    15
    Views
    3,959

    NO KIDDING! When did it become cool to go to...

    NO KIDDING! When did it become cool to go to someone else's brewery and put your stickers all over everything? I come in on a Sunday and there are brewery stickers all over my forklift, front door,...
  10. Thread: Glycol plc box

    by lhall
    Replies
    9
    Views
    1,024

    Automation Direct is a good source for PID...

    Automation Direct is a good source for PID controllers. https://www.automationdirect.com/adc/home/home?gclid=EAIaIQobChMI0tGB5ZXN4AIVhR9pCh0psglkEAAYASAAEgJQB_D_BwE#bodycontentppc
  11. Replies
    11
    Views
    1,339

    https://discussions.probrewer.com/showthread.php?4...

    https://discussions.probrewer.com/showthread.php?44318-Our-millroom-dust-collector&highlight=grain+dust+collector

    Build you one of these. It will keep the dust down and save your sinuses.
  12. Replies
    2
    Views
    1,256

    DME / Newlands auction

    https://www.bidspotter.com/en-us/auction-catalogues/infinity-asset-solutions

    Sad. I guess trying to find a buyer as a going concern didn't work out. I've had a brewhouse and tanks from both DME...
  13. Replies
    19
    Views
    2,273

    I think you'd want to scrub the gas coming off a...

    I think you'd want to scrub the gas coming off a fermenter to remove sulphur compounds and other undesirable volatiles before using it for anything. A lot of big brewers do this, but I'm not sure at...
  14. Replies
    5
    Views
    687

    I've never heard of anyone doing this, and can't...

    I've never heard of anyone doing this, and can't think of a good reason to shut off the bottom jacket, and a lot of reasons not to shut it off - yeast autolysis being the main one. Stratification is...
  15. Replies
    310
    Views
    117,727

    Jeff, You might try bumping your carb levels...

    Jeff,

    You might try bumping your carb levels up just a little. 2.4-2.5 isn't that much more, and the foaming will knock some out and let you cap on foam.
  16. Replies
    19
    Views
    2,273

    Jay, You do need a DO meter, and it's...

    Jay,

    You do need a DO meter, and it's something you will use daily in multiple locations once you have it, as part of your QC.

    When we got one, I thought that our procedures were pretty good...
  17. Replies
    10
    Views
    2,169

    Your best bet is to use 3/8" hose from the keg...

    Your best bet is to use 3/8" hose from the keg coupler up to the wall shank, and finish there with 3/16" ID hose to add the right amount of restriction. 3/8" ID hose has very little restriction -...
  18. Anthony, We do not use deaerated water for...

    Anthony,

    We do not use deaerated water for rinsing our bottles. We run a 24 head COMAC, and have found that by adjusting the speed, bowl level, and bowl pressure, we can get the bottles capping...
  19. Replies
    310
    Views
    117,727

    Those MAC valves are prone to sticking. If you...

    Those MAC valves are prone to sticking. If you follow the air line from the cylinder back to the MAC valve, that is the one that is sticking. You might try disassembling the valve, cleaning it out,...
  20. Replies
    9
    Views
    1,195

    CO2 is fine up to about 12 psi of restriction. ...

    CO2 is fine up to about 12 psi of restriction. Applying more than that will overcarbonate your kegs over time. You manage the restriction by the type of beer hose and the length. There is a ton of...
  21. Replies
    15
    Views
    2,268

    TGTimm, I would imagine the 35 gallon drum,...

    TGTimm,

    I would imagine the 35 gallon drum, with the addition of an anti-foam like Fermcap, would keep the foam down and let you vent the CO2 outside.
  22. The problem is that as you get closer to the cold...

    The problem is that as you get closer to the cold side temperature, the rate of heat exchange goes down fast. Plus, if you are using a cold liquor tank, you end up using all your cold liquor and not...
  23. Replies
    2
    Views
    881

    COLAs are no longer required for intrastate...

    COLAs are no longer required for intrastate sales. You still have to follow the requirements for a label, like the government warning and such. If it crosses state lines, a COLA is required by the...
  24. Replies
    9
    Views
    839

    The price difference is not that bad - our labels...

    The price difference is not that bad - our labels are around 2.2 cents each. Cut & stack used to be around 1 cent. We had an old Krones Rotina and messing with the glue every day was a nightmare. ...
  25. Replies
    9
    Views
    839

    Have you checked out pressure sensitive labels? ...

    Have you checked out pressure sensitive labels? You can get a new unit for ~$15,000. With the right substrate glue, and preferably labeling before filling, you can forget about cold-glue labellers.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4