Search:

Type: Posts; User: LTD Brewing

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    934

    Thanks for chiming in everyone. I did the math...

    Thanks for chiming in everyone. I did the math and if we used a 1.5" ball valve going into 125 gallon tank, assuming all oxygen is dissolved we'd be looking at roughly 12,000 ppb pickup. I know our...
  2. Replies
    6
    Views
    934

    DO Pickup From Moving Valve to Valve

    I'm looking for a few opinions and maybe some data on what people are seeing. Say you are moving your from the brite to 2 serving tanks. You setup a transfer hose with a valve on the end, sanitize,...
  3. Replies
    0
    Views
    525

    Wort Gravity Measurement

    Hi All,

    I am working on automating our common measurements during a brew day. When we are transferring wort from the MT to the kettle, we currently pull samples about every 15 minutes to check...
  4. Thanks!

    We were planning on having OSHA out at some point, I just want to do our due diligence first to ensure we get everything we know of corrected first, then have them out. Thanks for the advice and...
  5. Blocking Roof Access - OSHA Requirements?

    We are trying to beef up our safety program right now. We sent a couple of brewers to a safety training, where they were told that we couldn't block the access to our stairs (which in most cases...
  6. Replies
    10
    Views
    5,174

    Worth Every Penny

    You get what you pay for. You have to spend money to make money. All those cool old sayings...

    We pay way more than $600 per year, and it's worth every penny. For us it's all about ease &...
  7. Replies
    10
    Views
    5,174

    Touchbistro Is Nice For Certain Breweries

    We provide table service, which is a little different than most breweries. For us we needed something that runs like a restaurant. We use Touchbistro with Square as our CC processor. It's pretty...
  8. Thread: co2?

    by LTD Brewing
    Replies
    6
    Views
    3,343

    Go Bulk

    Unless there is something new and cool on the market, CO2 generator isn't within reach at 5 bbls. If you're going to run Nitrogen beers I would recommend a nitrogen generator. Most breweries have a...
  9. Replies
    7
    Views
    2,069

    Make Some Phone Calls

    Honestly, any information people give you on here is going to be what their health dept/dept of ag told them. They are all very, very different. I would recommend making lots of phone calls before...
  10. Replies
    2
    Views
    1,931

    StarShine

    It's hard to recommend a product to make your tanks shine again without knowing what the streaks are like/what is causing them. In general we use 5-Star's StarShine on the exterior of our tanks and...
  11. Tricky - It Depends On How You're Defining Things

    People often confuse aroma and bittering used in hop terms as being "what it smells like" and "what it tastes like." In reality the two things overlap and our brains rely heavily on both senses to...
  12. Replies
    3
    Views
    1,128

    First Reply!

    Thanks so much for the reply, Mike! Glad to hear your numbers are in the same ballpark. We have an employee who is concerned that it's too high. I have contacted our health department, but I...
  13. Replies
    3
    Views
    1,128

    Bump

    Has no one measured the air quality of their brewery, or is this just a dumb/easily answered question? Should we be concerned about CO2 levels, and has anyone made changes to their HVAC to improve...
  14. Replies
    3
    Views
    1,128

    Indoor Air Quality & CO2 Concentrations

    Hello Everyone!

    I'm wondering if anyone else has measured your indoor air quality (specifically CO2 levels) and what that looks like. We recently purchased a CO2 monitor and we were a bit...
  15. Health Department Requirement Questions- 3 Sink Rig & Growler Procedures

    Hey Everyone. I'm sure the regulations are discussed up and down, but they're quite frustrating...

    We just got through with our annual health inspection. We got a couple things that are...
  16. Replies
    3
    Views
    1,559

    Malt Mill Pulley Issue

    We have a pulley in our malt mill where the set screw continues to loosen causing the pulley to wobble (becomes unbalanced). We have tried locktight on it several times (blue and red) and it...
  17. Replies
    8
    Views
    7,548

    We picked up this bad boy from Harbor Freight...

    We picked up this bad boy from Harbor Freight (not the greatest place for quality products, but this has been solid for us).
    ...
  18. Replies
    3
    Views
    2,332

    Thanks for the reply!

    Hey guys! Thanks for the quick reply. I figured that a large supplier wouldn't sell hops that were bad, but you never know. We ended up piecing our hop order together from a few different...
  19. Replies
    3
    Views
    2,332

    Old Hops From Suppliers

    Hello All!

    As a new brewery, we recently started putting together our hop contracts for the future. For the time being, however, we are stuck purchasing what is available at the current spot...
Results 1 to 19 of 19