Search:

Type: Posts; User: pjbroyles

Page 1 of 2 1 2

Search: Search took 0.31 seconds.

  1. 64656 We used a vinyl cutter (cricut) to make...

    64656

    We used a vinyl cutter (cricut) to make labels for ours.
  2. Replies
    2
    Views
    981

    We are all bung sided on our fleet of 1/2 bbl...

    We are all bung sided on our fleet of 1/2 bbl kegs (~400) and have a washer specifically designed for them. If you aren't just bung them and wash them normally, then pop the bung and inspect with a...
  3. Replies
    5
    Views
    2,179

    Figure three kegs for every tap you have pouring...

    Figure three kegs for every tap you have pouring at a minimum.
  4. Replies
    4
    Views
    1,179

    I think I will try and get "co2" before it gets...

    I think I will try and get "co2" before it gets snapped up...
  5. Replies
    13
    Views
    15,135

    Every system is different, and your jump is not...

    Every system is different, and your jump is not as great in volume as some. I would start at 110-125% and do some side-by-side taste testing.
  6. Replies
    13
    Views
    15,135

    You can adjust your hop utilization factor in...

    You can adjust your hop utilization factor in your equipment profile in beersmith. I have been using it for five years in my brewery after making the leap from a homebrewer. Works great!
  7. Replies
    17
    Views
    4,428

    You hired him to brew beer YOUR way. That's the...

    You hired him to brew beer YOUR way. That's the problem with hiring a brewer as apposed to hiring an assistant to mold into the brewer you need for your operation. Right or wrong, your beer tastes...
  8. I may be wrong, and it may vary from state to...

    I may be wrong, and it may vary from state to state, but it was my understanding that pre-filled growlers are subject to the same labeling requirements as bottles (label approval etc.) Empty...
  9. Not exactly Seattle, they are in Sandpoint Idaho....

    Not exactly Seattle, they are in Sandpoint Idaho. Excellent supplier, speedy and good prices.

    http://www.clearwatergear.com/
  10. Replies
    5
    Views
    3,791

    Loaded question for sure with a lot of variables....

    Loaded question for sure with a lot of variables. Whatever you come up with, figure at least three kegs per tap handle. One serving, one backup and one in transit/cleaning.
  11. We started about five years ago in Washington...

    We started about five years ago in Washington state. There used to be another startup who started about a year before us and has since closed. They brewed a "test" batch while waiting for their...
  12. Replies
    7
    Views
    1,934

    Have dealt with Niko before and can vouch for...

    Have dealt with Niko before and can vouch for him. Good guy, good company. I am sure there is a snafu here somewhere, and am sure he will rectify it.
  13. Replies
    12
    Views
    2,326

    And therein lies the problem....

    And therein lies the problem....
  14. Replies
    5
    Views
    1,833

    We had some like that. We welded a lag bolt to a...

    We had some like that. We welded a lag bolt to a piece of re-bar threaded it into the bung via the bung hole. Pulled it up and grabbed it with needle nose pliers.
  15. Replies
    5
    Views
    3,981

    Yes they thread out. We got a bunch of them as...

    Yes they thread out. We got a bunch of them as well. We built a tool to remove them but have done it with needle nose pliers and screw drivers. Depends on how tight they are.
  16. Replies
    7
    Views
    2,121

    We used electrical conduit sweeps from an...

    We used electrical conduit sweeps from an electrical supplier to make the corners. Bought sweeping 90's and cut them as needed.
  17. Replies
    7
    Views
    2,121

    That's what we used. 4 years and counting....

    That's what we used. 4 years and counting....
  18. Thread: Boot Dryer?

    by pjbroyles
    Replies
    6
    Views
    4,648

    This...

    This is the one I have been using for years. No moving parts to wear out. Works like a charm.
  19. Replies
    18
    Views
    5,530

    Same here. Very confrontational, condescending...

    Same here. Very confrontational, condescending and snobbish until we took a bunch of handles from them. I waited for them to come knocking.
  20. Replies
    13
    Views
    6,088

    Have you looked at beersmith?

    Have you looked at beersmith?
  21. Replies
    33
    Views
    11,227

    I second that. On exit, have a thermometer...

    I second that. On exit, have a thermometer immediately followed by a throttling valve.
  22. Thread: Grundy nuts

    by pjbroyles
    Replies
    4
    Views
    1,590

    You got it!

    You got it!
  23. Thread: Grundy nuts

    by pjbroyles
    Replies
    4
    Views
    1,590

    I have a tap on order and a machinist ready to...

    I have a tap on order and a machinist ready to make them for me. I'll update you on the progress.
  24. Replies
    3
    Views
    2,920

    We have a CDC mash tun, 7bbl boil kettle (steam...

    We have a CDC mash tun, 7bbl boil kettle (steam fired) and 3 15 bbl fermenters we bought used 3+ years ago. The company is Cross Distributing Co and they are no longer in business.

    I think Mt...
  25. Thread: Keg branding

    by pjbroyles
    Replies
    4
    Views
    2,540

    We bought packaging tape from Uline with our logo...

    We bought packaging tape from Uline with our logo printed abut every six inches and wrap the kegs with it. Has worked well for 2+ years. Rarely have to replace it.
Results 1 to 25 of 45
Page 1 of 2 1 2