Search:

Type: Posts; User: liammckenna

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    154

    We have installed sump/digesters with overhead...

    We have installed sump/digesters with overhead discharge to join existing plumbing in one such situation here. Proper plumbing/venting of drains is required in all such situations. It is not ideal,...
  2. Replies
    10
    Views
    407

    Correct. You can vent to the rear of the unit,...

    Correct. You can vent to the rear of the unit, not the filler bowl/reservoir via the fob/overflow tubes.

    Good luck.

    Pax.

    Liam
  3. Replies
    10
    Views
    407

    There is a vent on the 'bowl' (reservoir of beer...

    There is a vent on the 'bowl' (reservoir of beer in machine) bowl is pressurized with CO2. Pressure of incoming beer slightly exceeds bowl pressure. Fill valves are three-way, typically one would...
  4. Replies
    10
    Views
    407

    Check this out. We used one for years. Works...

    Check this out. We used one for years. Works well. Simple operation. Blast shield is important too.

    https://www.probrewer.com/classified-ad/manual-4-head-counter-pressure-filler-bottling-unit/
    ...
  5. Replies
    4
    Views
    228

    The purple gear is the bee's knees... ...

    The purple gear is the bee's knees...

    https://www.beveragecraft.com/beer-line-cleaner-5l-1-3gal-beverage-system-cleaner-pipeline-fourteen-2-in-1-color-verification/

    Pax.

    Liam
  6. Replies
    7
    Views
    492

    Take a look at analysis below and assumptions. If...

    Take a look at analysis below and assumptions. If your incoming water is significantly colder, your HLT will need much more heat input. I would not do a 7 bbl with less than 10 bHP. Ensure your steam...
  7. Much safer with a blast shield. The occasional...

    Much safer with a blast shield. The occasional bottle will explode. Not cool. We used one like this for years. If operated reasonably, it yields a high quality fill. Simple and pretty rapid too.
    ...
  8. Replies
    6
    Views
    707

    Many ways to do this. Basically start with a...

    Many ways to do this.

    Basically start with a beer/stout about 1.3-1.5 vol CO2 and then nitrogenate to saturation.

    That can happen a number of ways: a custom nitrogenation plant (basically...
  9. We are fortunate that our tanks are all rated to...

    We are fortunate that our tanks are all rated to 2 bar.

    We 'spund' our fermentors to 2 bar (allow the fermentation to finish while building CO2 head pressure in the tank). This achieves about 2.5...
  10. Consider this: Chloride Stress Corrosion...

    Consider this: Chloride Stress Corrosion Cracking.

    http://www.ssina.com/corrosion/stress-corrosion-cracking.html

    As little as 10ppm can cause failure. I would remove skin and insulation around...
  11. Replies
    10
    Views
    1,011

    Thanks Dick. What approx. ratio of yeast to...

    Thanks Dick.

    What approx. ratio of yeast to sulfuric acid? A gallon of yeast with a 1/4 pint of sulfuric? Would Sulfamic work too replacing the Sulfuric, I wonder? The breakdown products thereof...
  12. Been wearing these for six months. TImberland...

    Been wearing these for six months. TImberland Pro. Good chemical resistance. Water proof. Exceptionally comfortable for a work boot. (I have hiked in them). Light (composite toe and shank)....
  13. Replies
    2
    Views
    962

    300 ppm Peracetic (or in combo with H2O2 - like...

    300 ppm Peracetic (or in combo with H2O2 - like p3-oxonia or Bioxy) in cold water. 5 min soak. Drain, do not rinse. Toss into tank. Measure accurately.

    Works every time for any nasties but only if...
  14. Replies
    8
    Views
    1,070

    This: 'The general specifications that cover...

    This: 'The general specifications that cover stainless steel kegs are ASTM A-967, ASTM A-380,
    ASTM B-912, ASTM D5276-92, ASTM D4003-92, ASTM D4577, ASTM D642, ASTM 117, ASTM
    D880-92, ASTM D3332-92,...
  15. Replies
    8
    Views
    1,070

    https://www.fosters.com/article/20121021/GJNEWS_01...

    https://www.fosters.com/article/20121021/GJNEWS_01/121029899
  16. Replies
    2
    Views
    1,045

    Alfa laval has a neat piece of kit as does...

    Alfa laval has a neat piece of kit as does Centec. Production of de-alcoholized beer is difficult. The process is susceptible to oxidation of substrate, unwanted removal of essential beer flavours...
  17. Replies
    2
    Views
    822

    With high percentage oat beers: 1/ mash and...

    With high percentage oat beers:

    1/ mash and wort pH - pay close attention. Adjust accordingly. I find they run high. if not adjusted appropriately, will lead to an 'oily' hop expression poor hot...
  18. Replies
    17
    Views
    15,567

    This shit is the bee's knees. Idiot proof....

    This shit is the bee's knees. Idiot proof. http://www.thonhauser.net/en-us/products/dispensing-hygiene/tm-desana-max-ic/

    Fall back is chlorinated caustic (KOH) like Diversey's (or whatever they...
  19. Replies
    7
    Views
    1,275

    If you need a shit ton on the cheap, can receive...

    If you need a shit ton on the cheap, can receive it now, ready to rock etc...

    Try these folk...nice peeps.

    https://juicedeals.com/

    Pax.

    Liam
  20. Replies
    6
    Views
    767

    What is the carbonation level of your beer? Does...

    What is the carbonation level of your beer? Does your filler allow you to snift? To the bowl/filler head? To atmoshpere? A combination of both? You need to extend that step. The bowl pressure on...
  21. Replies
    3
    Views
    913

    Difficult now that it is in keg. ...

    Difficult now that it is in keg.

    Disks/creamers come in multiple sizes in Europe. Can't seem to find any other than .25 or .3 mm here. I would recommend a .5mm orifice plate even temporarily if...
  22. Replies
    9
    Views
    1,973

    10% roasted barley 10% flaked (oats, wheat,...

    10% roasted barley
    10% flaked (oats, wheat, barley)
    80% pale

    The most basic, simple, reliable, dry irish Stout recipe. I typically add a little carastan to the mix.

    I don't really like...
  23. Replies
    7
    Views
    2,327

    I beg to differ. If you have an employee who is a...

    I beg to differ. If you have an employee who is a thief within your walls, you can call the police and have them arrested and charged with theft, if you wish. It may take some time for the charge to...
  24. THe BA's wastewater manual quotes a ratio of...

    THe BA's wastewater manual quotes a ratio of about 4:1 (water consumed to beer produced) - this means 3 volumes of waste for every volume of beer produced.

    These, however, are based upon self...
  25. Replies
    8
    Views
    1,418

    Recipes are largely worth the paper they are...

    Recipes are largely worth the paper they are written on.

    No matter how skilled you may think you are in that regard, thousands of people can easily do the same for free.

    I would suggest you...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4