Search:

Type: Posts; User: brain medicine

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    1,283

    Depends on your license. If your license is...

    Depends on your license.

    If your license is for brewery with no food requirement, you got alot of options. If food is required then you need to talk to licensing board.

    Many states allow...
  2. autocorrect there. should have been thermowell. ...

    autocorrect there. should have been thermowell. the ones with the kinda round plastic head on them, connected to tc fitting into tank.

    the issue is that there isn't a nice plug or outlet to plug...
  3. Temp controller for use with 3 wire thermocouple connector

    have a three wire thermocouple with the plastic round connector head on the new tanks. we've just used basic johnson/ranco type setups in the past, hollow thermowell and shove the probe down there,...
  4. Technically beer nut has threads, which is what i...

    Technically beer nut has threads, which is what i was referring to, for the whole assembly. I wasn’t clear, but actually meant “either” male or female on threading, but now realize the beer thread...
  5. Brewpub draft line tubing from tanks to pumps

    so we've got serving tanks that feed into a big trunk line and out to our bars, pushed by flojets. trunk line is the bev seal ultra tubing, which is kind of a pain in the ass to handle/work with...
  6. Abrasive? Seems like an odd choice for soft...

    Abrasive? Seems like an odd choice for soft material, no? Burn the rubber?

    In any case the Best we had on hand was fine tooth sawzall blade. Piece of cake. Didnt even need cleaning up.
    ...
  7. And send NDL the bill.

    And send NDL the bill.
  8. Lift the tank and set it on some cribbing. ...

    Lift the tank and set it on some cribbing. Stabilize it- tie downs, chains, etc. Remove the foot, and with a few rags wrapped around your air nozzle plug the thread hole and blast it with...
  9. they will price match too in many cases.

    they will price match too in many cases.
  10. whats the best device for cutting these hoses? ...

    whats the best device for cutting these hoses? all i can think of that we have on hand is just some fine tooth saw blades.
  11. If anybody is looking for the preformed clamps...

    If anybody is looking for the preformed clamps without buying 100 buckles and 100ft of banding, i found some here.

    http://https://www.pwmall.com/m-2284-band-it-idex-inc

    Not a huge selection...
  12. Aha. Now we’re talking. Ok, so it looks...

    Aha. Now we’re talking.

    Ok, so it looks like i need a tool, and do i want the center punch style or the “band lok” style of clamps? Not sure what the difference is there.
  13. Clamps for barbed T fittings on brewers hose

    Got some old brewers hose for cheap, wanna cut it up into very small lengths for cip with mobile pump. Say 2foot section for suction, 5ft for discharge- just enough to reach cip arm on biggest...
  14. Replies
    6
    Views
    425

    Weve done 4 installations at different projects...

    Weve done 4 installations at different projects and there hasn’t been a performance difference between any of them. Why pay more?

    Luckily our man resurfaced. Threw out his back and was off for a...
  15. Replies
    6
    Views
    425

    im just looking for trunk line. nothing else. ...

    im just looking for trunk line. nothing else. trying to get a good price as we have somewhere on the order of 300-325 feet of the stuff @10-12 product, so not an insignificant chunk of change.
    ...
  16. Replies
    6
    Views
    425

    draft glycol trunk line vendors

    anybody know of any vendors besides micromatic that make and sell their trunk lines?

    long story short, the guy I've bought my trunk line off of before has a source that is apparently in the...
  17. Replies
    3
    Views
    447

    you've only got internal cooling or external...

    you've only got internal cooling or external cooling.

    coils for the interior.

    exterior is a fermentation chamber you buy (upright fridge/freezer) or build DIY. some folks have attempted to...
  18. Replies
    9
    Views
    866

    Whats your preferred sulfate/chloride for hoppy...

    Whats your preferred sulfate/chloride for hoppy sour? Ive tried both ends of spectrum, didn’t see much difference. Is it ratio, or ppm levels?

    And just to note for OP, ive used conan in kettle...
  19. as i noted above, brewery equipment i.e....

    as i noted above, brewery equipment i.e. brewhouse gear might not be on tarriff. but our tanks were definitely hit for 10%. we appealed, but havent gotten any money back so i'm assuming the appeal...
  20. alot of haze can be from big whirlpool hop...

    alot of haze can be from big whirlpool hop additions. that's the real reason NEIPA is hazy as i've come to understand it.

    as jebzter notes, you should still whirlpool even if your pickup is a...
  21. The few times ive played with it were fails. The...

    The few times ive played with it were fails. The flavor fermented out completely. Considering this stuff is concentrate, i might give it another go at home to see what happens. But my guess is...
  22. im not sure they do, I thought most of the...

    im not sure they do, I thought most of the production moved even further south to Central America. either way, the Tijuana operation is nano size, so they just buy actual pineapples and mash them...
  23. Pineapple juice by the metric shit ton

    pretty much says it all. need a TON of pineapple juice. 55gal drums. tote cubes. whatever.

    anybody have any idea where i should look for this? hoping to get some leads before i go cold...
  24. WTF. Just bought the hinges from them, but didnt...

    WTF. Just bought the hinges from them, but didnt see that kind of seals. Ill take another look tomorrow. Thx
  25. That sounds exactly like what we need. Ill see...

    That sounds exactly like what we need. Ill see what i can find online.

    Thanks
Results 1 to 25 of 350
Page 1 of 14 1 2 3 4