Search:

Type: Posts; User: gitchegumee

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    2
    Views
    235

    Found that the plastic knob that adjusts the...

    Found that the plastic knob that adjusts the dosing pump rate has a set screw which locks it to the shaft. Plastic threads stripped. Need new knob! Or thread another spot for set screw. Thanks...
  2. Replies
    2
    Views
    235

    Velo operation help!

    I wanted to minimize my Velo filter pump output, so I turned it all the way down. Great. Now it's disengaged totally and I can't figure out how to engage the metering dial to the threads that allow...
  3. CIP pump

    Pump it in through one of the connections in the brewery.
  4. Replies
    2
    Views
    485

    Still looking.....

    If you have a Velo vertical filter 2-4 square meters, then I've got a job for it. PM me and we'll make a deal. Cheers!
  5. pH?

    What was your wort pH? If it was low, your grain went slack. That'll do it.
  6. Replies
    5
    Views
    430

    If your cider is warm...

    ...and you serve it cold from a jockey box, then you want your CO2 pressure high. Very high. Carbonation tables rarely go that high. Find one that does. You need a stable temperature and a stable...
  7. Replies
    1
    Views
    362

    Rexam cans with Crown ends?

    Seems like specs are close, but I'd like to know that they are compatible. Could someone please offer me confirmation either way? Thank you!
  8. Replies
    5
    Views
    12,230

    Biggest reason I use them....

    A CLT does help give you consistent knockouts with regard to temperature year round when municipal/ground water temperatures change. But more importantly I use them to receive filtered water. You...
  9. Replies
    15
    Views
    1,214

    Convection....

    The beer carbonates faster while cooling because it is rolling inside the fermenter. Convection of cooling jackets bring undercarbonated beer to the liquid/gas interface and promotes faster CO2...
  10. Replies
    2
    Views
    485

    Still looking.....

    Check your bone yard! We have a very nice home to offer it....
  11. Replies
    9
    Views
    629

    Hey Dick....

    Tried to message you, but your inbox is full....
  12. Replies
    5
    Views
    608

    See attached .pdf.....

    Some older literature from Cask is all I found in my files, but there are more studies out there.... Good luck.
  13. Replies
    9
    Views
    629

    A few thoughts...

    Sprayballs are not designed to clean by impingement, but instead by the mechanical action of a cascade. So a gentle cascade over the entire surface to be cleaned is sufficient. More than that can...
  14. Replies
    5
    Views
    608

    Why?

    What purpose would that serve? There is research that shows counterpressure increases oxygen pickup. And if it reduces foam to the point where you are not seaming on foam, that would exacerbate the...
  15. Ouch!

    Maybe you're in the market for PRV too! We had very similar tanks at Atlanta Brewing Company in the mid-90's. Not sure but could be Mueller. Other great source of parts like this is Archon...
  16. Replies
    0
    Views
    148

    #202 ends wanted!

    Looking for red or green tab #202 ends. If you have left-overs, I'd give you fair value. Thanks!
  17. Replies
    0
    Views
    126

    #202 ends wanted!

    Looking for red or green tab #202 ends. If you have left-overs, I'd give you fair value. Thanks!
  18. Replies
    3
    Views
    266

    Go LED.

    If you have a typical clear lens on the kettle penetration, then you can use any of a number of standard LED lights meant for recessed accent lighting. I like the fact that they don't get so flippin...
  19. Replies
    5
    Views
    420

    I like Spirax equipment...

    Can't go wrong with time-tested, bullet-proof, solid design. Spirax isn't the only steam equipment manufacturer, but it's definitely my first choice. Look at their AV-13 which I put on a tee with...
  20. Be very, very careful...

    I have not heard one promising report of Chinese bottling line manufacturers. I've used quite a few from other countries and even good ones have their bad days. But for sure stay away from Gongda,...
  21. Replies
    5
    Views
    420

    Maybe add more air vents?

    I always include separate air vents at the top of the jackets. Even with air vents on steam traps. Sounds to me like air. Hard for that air to be discharged from bottom of jacket through the trap.
  22. Been there...

    I've rigged three systems like you are talking about doing it. It's the best solution for many breweries. One system features dual 4hp Danfoss roof-mounted condensing units and a single indoor...
  23. Replies
    2
    Views
    347

    No picture today...

    Seems to be fairly typical bulkhead compression fitting--but not standard size. Don't want to disassemble it until I have replacement. Yes, stainless/stainless is bad. But the ferrules could be...
  24. Replies
    2
    Views
    347

    Brass parts in Velo...

    I've got a brass bulkhead fitting on my Velo erosion filter stir paddle. It allows manual stirring of the filter aid while sealing the erosion section. Would love a suggestion to replace this with...
  25. Replies
    4
    Views
    602

    My FRP sucks.

    After 10 years of use, my FRP has delaminated from the substrate. Cheap, but not worth it IMO. I like the product I bought from Extrutech plastics: http://www.epiplastics.com/index.html
    Their...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4