Search:

Type: Posts; User: DGuggenb

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    486

    Wheat Beers

    I've found with our hefeweizens that towards the end of the keg there will be excess foam on top, which would make its way through the line even before the keg was finished. This was when we were...
  2. DIY Option

    There's also the option to build your own from window air conditioners. Cost each would be $300-400. Works the same way as a normal glycol chiller. You'll just have to search around if this is...
  3. Along these lines, you can actually have a small...

    Along these lines, you can actually have a small high-pressure diaphragm pump that Tees into the line you are using to put the sparge water in. Have the inlet tube from the diaphragm pump go into a...
  4. Replies
    3
    Views
    510

    Yeast and trub will settle out in the sample...

    Yeast and trub will settle out in the sample port. You can try puling a small sample first to get rid of the stuff in the sample port and then take a second pull and see if that comes out clear. Then...
  5. Thread: Grain Mill

    by DGuggenb
    Replies
    6
    Views
    579

    I had quite a few discussions with the guy before...

    I had quite a few discussions with the guy before I was ready to purchase it. In this case they do appear to rotate at the same speed. Two roller and three roller mills that aren't geared together...
  6. Thread: Grain Mill

    by DGuggenb
    Replies
    6
    Views
    579

    I just built a grain mill using the geared...

    I just built a grain mill using the geared version. We haven't started production yet so I can't comment on the durability, but as long as you have enough power and belt tension, it seems to work...
  7. Replies
    11
    Views
    1,183

    What I meant was that if you didn't even have...

    What I meant was that if you didn't even have stir plates and just fermented three 20 liter batches that you would have enough yeast from that. If you incorporate a stir plate into this, you might be...
  8. Replies
    11
    Views
    1,183

    Correct, I did cell counts on the starters that I...

    Correct, I did cell counts on the starters that I made. Some of these were from vial/pouches, some were from harvested yeast. I don't know if you already do cell counting, but if you don't then this...
  9. Replies
    11
    Views
    1,183

    This is based on a calculator from brewer's...

    This is based on a calculator from brewer's friend that comes from a Braukaiser study/formula if I remember correctly. I've done some yeast counting in the past on starters based off of this method...
  10. Replies
    11
    Views
    1,183

    Starter Option

    You can also use the Maelstrom from Northern Brewer. https://www.northernbrewer.com/maelstrom-stir-plate . We're getting ready to launch with our 2bbl pilot system while we're waiting for...
  11. Replies
    10
    Views
    3,309

    The periphery speed can be set to the same speed,...

    The periphery speed can be set to the same speed, the difference then would just be the length of the roller which is what would give the higher throughput. The peripheral speed is just the RPMs...
  12. Replies
    0
    Views
    1,349

    Nano-brewery Mill new and used for sale

    SOLD

    I've got a used nanobrewery mill for sale. This is a monster mill MM-3Pro, 3 roller mill with hardened rollers. The motor is a 1hp TEFC motor speed reduced to mill about 30 lbs/minute keeping...
  13. Replies
    10
    Views
    3,309

    Roller Speed

    I believe the intent is the speed at which the grain is moving through the gap. RPM just relates to the actual number of times the roller rotates per minute, not the speed at which the grain is...
Results 1 to 13 of 13