Search:

Type: Posts; User: augiedoggy

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. There are many options here that can be used with...

    There are many options here that can be used with an rtd... ranging from hundreds of dollars to some of the the cheap inkbird type hysteresis controllers (the $99 prewired inkbird pid box uses a 3...
  2. well the motor is only 170rpm so its not all that...

    well the motor is only 170rpm so its not all that fast Ive never times it to be honest but 8 months later it still looks new and works fine getting use every sunday.
  3. Replies
    5
    Views
    614

    same arm that came with my 3bbl sungood setup. I...

    same arm that came with my 3bbl sungood setup. I thought this sort of thing was losing popularity since it oxgenates the sparge water vs a regular hose on the mashbed?
  4. Replies
    6
    Views
    773

    The majority of the cost is due to supply and...

    The majority of the cost is due to supply and demand of UL listed control panels... if its just a pid based panel realistically its likely less than $1000 in hardware and the rest goes for assembly...
  5. I reassembled and tested everything with no...

    I reassembled and tested everything with no issues... It would have been "best" if thier were some sort of documentation with the unit or at least on thier website... I understand they dont make...
  6. Thread: Grain Mills

    by augiedoggy
    Replies
    6
    Views
    491

    We have both a mm3 (non pro) and the kegco 3...

    We have both a mm3 (non pro) and the kegco 3 roller and have decided to use the kegco 3 roller and keep the mm3 for backup. we have a 3 bbl system. We have motorized the kegco and have been using it...
  7. I have the same issue with my sabco chiller......

    I have the same issue with my sabco chiller... the numbers on the gaskets and plates where all way out of order some of the plates were numbered with a magic market and some were not.. I cannot find...
  8. Replies
    8
    Views
    692

    it really depends on how closely they look at...

    it really depends on how closely they look at your drawing since most of the breweries ive been too do what you are describing. But yeah, we had the license and when we went to make an amendment we...
  9. Replies
    2
    Views
    808

    Good to know on the tariff thing... My dealings...

    Good to know on the tariff thing... My dealings with Gavin were very positive too, The only thing that was a little unnerving for me was figuring out how to estimate my customs fees which wasnt so...
  10. Replies
    4
    Views
    242

    We might be able to provide more help if perhaps...

    We might be able to provide more help if perhaps you shared what element and housing your using? pics maybe?
  11. Just an update on this pump since Ive gotten a...

    Just an update on this pump since Ive gotten a lot of private messages about it and we've been using it for 6 months now.

    It has been working flawlessly for our needs so far. I have been...
  12. Replies
    8
    Views
    692

    We are in a similar boat... It took us over 2...

    We are in a similar boat... It took us over 2 years to open due to doing the renovations ourselves while working our day jobs and unforeseen delays from inspectors and such. Also the rules changed so...
  13. Understood, so its using a duty cycle or ssvr...

    Understood, so its using a duty cycle or ssvr relays to control output similiar to the manual duty cycle mode on a pid controller with the manual option build in would but the knob control makes it...
  14. I just wanted to follow up that I did end up...

    I just wanted to follow up that I did end up going with 4 5500w elements and with my single phase power my control panel needed a minimum of 100a to do this. (I went with 2 60a gfci circuits ).

    ...
  15. Replies
    3
    Views
    595

    I realize things are different in the states but...

    I realize things are different in the states but I was quoted by as forum sponsor for 3bbl jacketed unitanks and can say the price is less than half whats mentioned above.. even with customs and...
  16. Replies
    3
    Views
    471

    I am curious about what is really needed myself....

    I am curious about what is really needed myself.
    We are able to control temps on all four of our plastic 3bbl conicals in a 55-60 degree avg room with one little 1/3hp chiller right now. (You might...
  17. Replies
    1
    Views
    399

    We have a 3bbl, we use mostly 3/4" ID santoprene...

    We have a 3bbl, we use mostly 3/4" ID santoprene hoses but I have some 1" and even 1.5" ID hoses we use with our 3/4hp chinese sanitary pump we bought on ebay for CIP and cleaning kegs as well as...
  18. Replies
    4
    Views
    509

    I cant give you a ball park value because you...

    I cant give you a ball park value because you never stated what wattage or voltage the elements are?
    This could help,...
  19. Replies
    4
    Views
    509

    just look for the ohms reading across each one......

    just look for the ohms reading across each one... if they are good they will all read relatively close. the reading actually depends on the wattage and voltage (208 vs 240) ...
  20. How does it control a steady boil? Most pid based...

    How does it control a steady boil? Most pid based systems use manual duty cycle mode for the actual boil to get a smooth consistent boil and to be able to dial in your boil off rate.. in PID mode it...
  21. Yes the pump works fantastic, I usually throttle...

    Yes the pump works fantastic, I usually throttle it down a bit with a butterfly valve as its super strong. Using it with a cheap sprayball on my plastic conicals that have stainless cooling coils in...
  22. Replies
    8
    Views
    786

    did you request the elements in the MT? I have...

    did you request the elements in the MT? I have the same kettles as you from the same forum sponsor I assume and there is no elements in my mash tun? this would seem to me to be some sort of custom...
  23. depends on the amount of boiloff desired for us.....

    depends on the amount of boiloff desired for us.. also 4 5500w elements 60% is a good strong boil but little boiloff.
  24. Replies
    8
    Views
    786

    ok I think there a communication issue and...

    ok I think there a communication issue and misunderstanding about what is what.

    It sounds like you are trying to use the HLT or BK as the Mash tun? I have the same system bought direct from...
  25. Replies
    37
    Views
    5,760

    been using mine... more than powerful enough to...

    been using mine... more than powerful enough to clean 3 kegs at a time. in fact I still have to throttle it down.
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4