Search:

Type: Posts; User: Todd Hicks

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    3,664

    Run all of your tanks for an hour or two and...

    Run all of your tanks for an hour or two and purge out the air. Keep an eye on the glycol chiller as sometimes air can trip the glycol supply level sensor and shut down.
  2. Use the Midco modulator for your burner. One...

    Use the Midco modulator for your burner.

    One the controls, you can use any type controller that is 0-10vdc. On the output of the 0-10vdc leg, also install a reostat type knob to adjust th burner...
  3. Replies
    11
    Views
    3,664

    Alternative valve from McMaster-Carr

    This valve is only $62 for a 3/4" that is adjustable 0-50 psi, less expensive than the 1" npt non adjustable 30 psi as the other one listed in this thread. This one is probably better suited. 3/4"...
  4. Replies
    2
    Views
    502

    Conical fermenters deserve Spunding valves

    https://discussions.probrewer.com/showthread.php?63571-carbonating-with-no-carb-stone-spunding-plus-temp-amp-head-pressure
    ...
  5. Manual keg filler with fob

    Read these threads.

    The consensus seems to generally be that the GW Kent Fob Fillers are pretty reliable and simple. I use a TC manifold with 8 of these to rack kegs off of a 60 bbl bright tank. ...
  6. Replies
    11
    Views
    3,664

    Put a large face pressure gauge before the pass...

    Put a large face pressure gauge before the pass through valve so you can dial in the adjustment.

    Also, put in isolation ball valves before and after the bypass assembly for emergency shutdown or...
  7. Replies
    4
    Views
    461

    Use high quality hydrailic QD valves. Probably...

    Use high quality hydrailic QD valves. Probably find them easily at McMaster Carr
  8. Thread: Brewery Cat

    by Todd Hicks
    Replies
    8
    Views
    1,043

    Just make sure that there is a hidey space for...

    Just make sure that there is a hidey space for the cat to be safe in when too many people begin to get annoying or when the forklift is in operation.
    They will get territorial and do their jobs well.
  9. Replies
    3
    Views
    1,104

    Could use a CIP cart with heated reservoir.

    Could use a CIP cart with heated reservoir.
  10. Replies
    15
    Views
    1,648

    We would need to know much more about the...

    We would need to know much more about the equipment and your setup in order to offer suggestions.

    Volume? Type of tank? Jacketed? Temperature of beer? Pressure rating? Ports on tank?

    Why not...
  11. Replies
    10
    Views
    1,396

    $15 is only the vent valve, assembles tube with...

    $15 is only the vent valve, assembles tube with ball, and beer nut barb fitting.
  12. Replies
    9
    Views
    1,078

    You have plenty of hp. Why no side jackets on...

    You have plenty of hp.

    Why no side jackets on the kettle?

    Need more surface area. On any system, you should be boiling by the time the kettle is full.
  13. Replies
    5
    Views
    660

    Whoudln't this work? ...

    Whoudln't this work?

    https://www.gwkent.com/pico-carbonator.html


    Pico Carbonator 7/8" x 5" Stone with TC 1.5"

    Catalog #85-59
    $109.00
  14. Replies
    11
    Views
    1,089

    The check valves weren't necessary as there...

    The check valves weren't necessary as there shouldn't be any back flow. They may put some strain on the system, but I don't know. The return line should never really have any pressure on it as it...
  15. Replies
    11
    Views
    1,089

    solenoid before the inlet. On recent builds,...

    solenoid before the inlet.

    On recent builds, I put them high up on the tanks rather than lower directly at the inlet. Just make sure you can get easy access to the solenoid valves and isolation...
  16. Replies
    11
    Views
    1,089

    Go over to the other thread ...

    Go over to the other thread

    http://discussions.probrewer.com/showthread.php?74359-Anyone-out-there-use-gw-kent-temp-controllers-Wiring-question-please-help
  17. continued. 5886358864

    continued.

    5886358864
  18. Use normally closed solenoids with a ball valve...

    Use normally closed solenoids with a ball valve on both sides of the solenoid valve to isolate them for cleaning or to throttle back the flow if necessary.

    On the end of the loop, do not use a...
  19. Replies
    21
    Views
    2,804

    Not to directly weigh in on the costs and returns...

    Not to directly weigh in on the costs and returns here, but here are my practical opinions.

    1) If you have a 10 bbl system, then brew 10 bbl batches. Half brews will lower your grist utilization,...
  20. Replies
    11
    Views
    1,089

    In through the lower jacket glycol INLET, and out...

    In through the lower jacket glycol INLET, and out through the topmost jacket OUTLET. For small tanks with multiple jackets, it is alright to go into the cone lower inlet first, out of the cone...
  21. From AutomationDirect.com SQM08D RELAY SOCKET,...

    From AutomationDirect.com

    SQM08D RELAY SOCKET, FOR QM2 SERIES CUBE RELAYS WITH SQUARE BASE 3.25

    QM2N1-D24 CUBE RELAY, 24VDC COIL, 2PDT, 5A, LED INDICATOR 4.75

    PSB24-060-P POWER...
  22. It is really simple. 1. You need a power...

    It is really simple.

    1. You need a power supply. The one in the pic will run 2 tanks. This one is from AutomationDirect 110vac - 24vdc I will post me parts list soon
    2. 24vdc relay.
    3....
  23. I was able to to a pretty good caramelization...

    I was able to to a pretty good caramelization fake decoction by pumping my first wort to kettle, heating it up to boil, then pumping back into the mash before starting vorlauf. You could heat the...
  24. 582915829258293

    582915829258293
  25. Is it the round ones that hang off of your...

    Is it the round ones that hang off of your fermenter with a hook?

    If so, you will need a power supply, relay, water proof junction box and a few other items.
Results 1 to 25 of 261
Page 1 of 11 1 2 3 4